Spc manual 3rd edition pdf. AIAG Production Part Approval process PPAP 4th Edition

Spc manual 3rd edition pdf Rating: 9,5/10 1609 reviews

Download Aiag Spc Manual 3rd Edition PDF Book

spc manual 3rd edition pdf

Much of the work of managing a measurement system is directed at monitoring and controlling variation. Further classifications may be reworkable, salvageable or scrap. Equipment is only one part of the measurement process. Proven measurement methods may provide more reliable operation. Traceability is the chain of calibration events originating with the calibration standards of appropriate metrological capability or measurement uncertainty. Terminology The discussion of the analysis of measurement system can become confusing and misleading without an established set of terms to refer to the common statistical properties and related elements of the measurement system. Many activities, such as draining air filters daily, lubricating bearings after the designated number of operating hours, etc.

Next

Aiag msa 4th ed

spc manual 3rd edition pdf

It has been constructed to be a self-contained discussion about the process of developing a measurement process quotation package, obtaining responses to that package, awarding the project, completing final design, developing the measurement process, and, finally, marrying that measurement process to the production process for which it was created. Deming used to describe the effects of tampering. The property called bias refers to the location of the data relative to a reference master value, and the property called variance refers to the spread of the data. The 3 Portions of this chapter adapted with permission from Measurement Systems Analysis - A Tutorial by G. If the measurement system Cp index were itself 1. Heaphy, The Third Generation, 1987, 1998.

Next

AIAG SPC

spc manual 3rd edition pdf

Traceability is an important concept in the trade of goods and services. Purpose The purpose of this document is to present guidelines for assessing the quality of a measurement system. Data obtained from such a machine can be very useful for analyzing a manufacturing process. The same measurement, on the same characteristic, at the same area of the process, over an extensive period of time is evidence of a lack of learning or a stagnant measurement process. Following that is a section which addresses its impact on the process decision. These include: 1 Adequate discrimination and sensitivity.

Next

Download Aiag Spc Manual 3rd Edition PDF Book

spc manual 3rd edition pdf

It is not intended to limit evolution of analysis methods suited to particular processes or commodities. If the reader chooses to increase the coverage level, or spread, of the total measurement variation to 99. The actual degree of involvement or implementation in many of the activities below should be driven by the particular measurement system, consideration of the supporting gage control and calibration system, profound process knowledge, and common sense. The planning stage will set the course and have a significant effect on how well the measurement process operates and can reduce possible problems and measurement error in the future. The measurement and analysis activity is a process — a measurement process. Another guide would be the level of tolerance assigned to a specific dimension. In order to control the measurement system variation: 1 Identify the potential sources of variation.

Next

AIAG Production Part Approval process PPAP 4th Edition

spc manual 3rd edition pdf

Any and all of the management, statistical, and logical techniques of process control can be applied to it. The data, or some statistic calculated from them, are compared with statistical control limits for the process, and if the comparison indicates that the process is out of statistical control, then an adjustment of some kind is made. The measurement system must be stable and consistent. Other properties, such as cost, ease of use, etc. The difference in the observed Cp of 1. P 13 For complex measurement systems, a flow chart is made of the measurement process.

Next

AIAG Production Part Approval process PPAP 4th Edition

spc manual 3rd edition pdf

This may satisfy initial implementation requirements, but this documentation does nothing with regard to defining potential wear points, suggesting possible trouble areas or describing how to use the process. In general, an analytic study is one that increases knowledge about the system of causes that affect the process. This is equivalent to using the multiplier of 6 in the historical approach. Are the part location and fixturing possible sources of variation? The benefit of using a data-based procedure is largely determined by the quality of the measurement data used. The Measurement Life Cycle concept expresses the belief that the measurement methods may change over time as one learns and improves the process. This rule of thumb was intended as a practical minimum starting point for gage selection. Independent measurements imply that the traceability of the secondary measurement process is derived from a separate chain of calibration events from those used for the initial measurement.

Next

Download Aiag Spc Manual 3rd Edition PDF Book

spc manual 3rd edition pdf

Since there may be several levels of concept approvals to be carried out, and possible environmental changes and the potential of team members changing, the measurement process project could falter or even fail. These are based on customer requirements and the functionality of the subsystem or component to the total system. Rule 4: Adjust the process to the point of the last measurement. This is accomplished by determining whether our process is in statistical control i. Simple standard measurement tools like micrometers or calipers may not require this in-depth strategy and planning.

Next

Aiag msa 4th ed

spc manual 3rd edition pdf

Management is also responsible for ensuring that those properties are used as the basis for selecting a measurement system. It provides the user with possible alternative routes to reach the desired destinations troubleshooting guides or diagnostic trees if the main route is blocked or closed. P 7 F is used to represent the six essential elements of a generalized measuring system to assure attainment of required objectives. Initial responsibility for this may lie with the product design engineer, dimensional control, etc. Then adjust the process in an equal amount and in an opposite direction from the target.

Next